Search results for: 'coil+when+19+64+they+8335+easi+nail+end'

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Waterbased formula is more environmentally friendly and easy to clean up. Whip-End Dip was designed to seal the end of a rope to prevent fraying or unraveling. Learn More

Lock washers are a critical component to through bolts on wood poles. Pole shrinkage mandates the use of double coil lock washers to keep pressure on the nut and bolt to prevent loosening. Learn More

This electric handheld unit cuts and fuses the ends of polyester and nylon ropes and webbing. Easy to use and long lasting blades. heats up when trigger is pulled and cools when released. Learn More

The perfect size for light and tower rescues. Fits ropes from 8mm to 1/2". Features built in safety cam for use in "jigger" or "short haul" systems. Use with CMI micro single or double pulley 3:1 or 4:1 mechanical advantage systems. Features a centered bronze bushing. Strength: 7000 lbs. The CMI Single Micro Hauler is 154 mm. tall, 53 mm wide, and 40 mm. thick and 19 g. Learn More

TRAC PLUS Zip Line Trolley, They cannot be dropped, thanks to the VERTIGO WIRE-LOCK carabiner, simplifying their functionality Learn More

Rope thimbles protect the rope from wear whenever you have a fixed loop in the end of the rope, whether the rope is tied, spliced, or swaged. Learn More

These lobster Claws are a unique, non-adjustable set of positioning / safety lanyards designed specifically for program high ropes courses. Learn More

The Head Rush Impact Trolley Sheave Replacement Kit allows you to replace your Impact Trolley sheave assembly should they wear out or become damaged. Learn More

The Head Rush Impact Trolley Handle Replacement Kit allows you to replace your Impact Trolley T-Handle handles should they wear out. Learn More

We offer three different style of pilot auger bits for 1/2" lags for ropes course decks, zip line decks and general deck construction for 1/2" & 5/8" lag bolts Learn More

The Impact Trolley Cover Plate Replacement Kit allows you to replace the Cover Plates on your Impact Trolley should they wear, get misplaced or damaged Learn More

Carriage Bolt w/Nut & Washer, The square neck under the round head will seat into the hole in the wood to prevent the head from turning. Because they are used with wood, carriage bolts are rarely high strength and virtually always supplied in a standard ASTM A307 specification. Learn More

Snap hooks are recommended as they are easier for small hands, more ergonomically friendly and are permanently attached to the lobster claws. Learn More

UltraSonic Finish: the core and the sheath are bonded together at the rope ends by an ultrasonic process called UltraSonic Finish; gives greater durability and avoids frayed ends. Learn More

Kong Futura Hand Ascender, It is extremely small though easy to use, weighs only 125g, and comes with two different sized handles for ergonomic customisation Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

This innovative, all-in-one Pulley/Auto belay for fall protection is lightweight and easy to use. Auto belay pulley Locks in either direction (right or left) while climbing up or down. Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

Mailion Rapid Links (aka "Rapides" or "Quick-Links") are steel screw-links designed for fastening lengths of chain together on ropes courses and zip lining. They provide critical connections for trolleys, balay devices, cables and cable hardware on a zip line. Learn More

The VERTIGO TWIST-LOCK carabiner is designed for use on progression lanyards. Its ergonomic design and automatic locking system facilitate manipulations when passing intermediate anchors. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

EverFlex treatment: special thermal treatment stabilizes the core strands and improves consistency; offers excellent grip and consistent handling over time. Learn More

Red Anodized Aluminum sideplates, 2 3/8" Glass-filled Celcon sheave, n/a, and Stainless Steel axle. The original rope pulley! Durable design, great action, light weight and easy to use. Learn More

Special thermal treatment stabilizes the core strands and improves consistency; offers excellent grip and consistent handling over time. Learn More

PetzlAVAO SIT Zipline/Work harness, With a ventral attachment point that distributes the load between the waistbelt and the leg loops during suspended work Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

The TOP chest harness transforms the AVAO SIT, FALCON and SEQUOIA SRT seat harnesses into fall arrest harnesses. The foam shoulder straps are widely spaced to reduce neck chafing. Learn More

Dry treatment makes the rope more resistant to water, dirt and abrasion; handling, grip and other characteristics are retained longer in cold, wet conditions. Learn More

It provides increased friction for single ropes when rappelling or lowering, without extra gear or the need to open the carabiner Learn More

The Fat Cat is from a line of proven performers for zip line operations: Robertson Mountaineering. This specialized design works great for the thicker and larger 1/2" - 3/4" cables used more and more by zip line tours and canopy tours. Learn More

The Zorber Shock absorbing unit is compact and lightweight. When a 220 pound weight is dropped six feet, the maximum arresting force will be less than 900 pounds. Learn More

Our Machine Bolts are hot dip galvanized, forged steel, quenched and tempered and are sold with hex nuts attached. Round or square washers and lock washers can be added separately. Learn More

When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Trapeze bar designed for use on ropes challenge courses: leap of faith. Our Trapeze Bar is made from 1-1/2" solid high density PVC. Learn More